Bathroom tile and flooring across San Diego County
Tile is the most visible surface in the bath, and the most likely to fail when it is installed over the wrong substrate. We connect you with insured local crews that handle substrate prep, Schluter Kerdi or RedGard waterproofing, tile layout, and grout selection for shower walls, bathroom floors, and heated floor systems.
What's included in bathroom tile?
- Substrate inspection and replacement of rotten or soft backer board, subfloor, or mud bed
- Schluter Kerdi, RedGard, or PVC liner waterproofing in the shower pan and on wet walls
- Shower wall and curb tile with proper slope to drain, plus preformed niche or bench tile
- Bathroom floor tile in porcelain, ceramic, marble, or natural stone with crack-isolation membrane
- Heated floor mat install (Nuheat, Schluter DITRA-HEAT, or SunTouch) with a dedicated GFCI wall control
- Grout, color-matched silicone at changes of plane, and a final seal on natural stone
When do you need bathroom tile?
- Existing grout is crumbling, tile is loose, or you see water stains on the ceiling below the bath
- You are switching from a fiberglass tub surround to a real tile surround
- You want a heated floor to take the chill off tile in winter
- The current 1-inch mosaic floor is dated and you want a 12x24 or 24x24 large-format porcelain
- You are refreshing the floor without a full remodel and want new tile laid over a sound substrate
What do homeowners ask about bathroom tile?
How much does bathroom tile cost in San Diego?
A bathroom floor retile in San Diego runs $1,800-$4,500 for a typical 5x8 bath with porcelain. A full shower wall retile with new waterproofing lands at $3,500-$9,000. Heated floor systems add $1,200-$2,500 depending on square footage. Material is the biggest cost driver: porcelain starts around $4/sq ft, marble and handmade zellige can run $20+/sq ft.
How long does bathroom tile installation take?
A floor-only retile with proper substrate prep finishes in 2-4 days. A full shower wall and floor with waterproofing runs 5-10 days on site. Heated floors add a day for mat install and a separate wall-control rough-in. Tile needs 24-48 hours to set before grout, and grout needs 24-72 hours to cure before shower use.
What is the best tile for a San Diego bathroom?
Porcelain tile is the most popular choice for San Diego bathrooms: it is dense, low-porosity, slip-resistant when textured, and rated for wet areas. Large-format porcelain (12x24, 24x24) reads modern and cuts down on grout lines. Natural stone like marble or travertine looks great but needs annual sealing and more careful cleaning in hard-water zones.
Do I need to waterproof behind the tile?
Yes. The tile and grout are not waterproof on their own. Behind them you need a proper waterproofing system: a PVC liner in a traditional mud pan, or Schluter Kerdi membrane over Kerdi-Board or DITRA. In San Diego, inspectors will fail a shower without a visible waterproofing layer. The crew always uses sheet membrane or liquid-applied RedGard over cement board.
Can I install heated floors in an existing bathroom?
Yes, in most San Diego bathrooms the crew installs an electric radiant mat (Nuheat, Schluter DITRA-HEAT, or SunTouch) between the subfloor and the tile. The mat is on a dedicated GFCI circuit, controlled by a wall control in the room. We add 1-2 days to the tile schedule and 1-2 days for the electrical rough-in and trim.
Where do we offer Bathroom Tile in San Diego County?
We provide bathroom tile in every city and community in San Diego County. Pick your city for local climate notes and service specifics.
See bathroom tile in all 67 cities
Need bathroom tile in San Diego County?
Leave your details on the line or send the form, and we route you to a local crew.